mad00070dem MN101CA2 series type MN101CA27 mn101 cfa2d internal rom type mask rom flash rom (byte) 16k 64k ram (byte) 0.5k 2k package (lead-free) lqfp064-p-1414 minimum instruction execution time 0.25 s (at 2.7 v to 3.6 v, 8 mhz) 0.50 s (at 1.8 v to 3.6 v, 4 mhz) 62.5 s (at 1.8 v to 3.6 v, 32 khz) ? interrupts reset. watchdog. external 2. external 6 . timer 0 . timer 1 . timer 6 . time base ? timer counter 8-bit timer 2 timer 0 .................. square-wave/8-bit pwm output. simple pulse width measurement timer 1 .................. square-wave output timer 0, 1 can be cascade-connected time base timer: one-minute count setting watchdog timer 1 remote control carrier output ? i/o pins i/o 16 : common use. speci?ed pull-up resistor available. input/output selectable (bit unit) input 9 : common use. speci?ed pull-up resistor available ? display control function lcd: 32 segments 4 commons (1/3 or 1/4 duty) ? special ports buzzer output. remote control carrier output. high-current drive port ? electrical charactreistics (supply current) parameter symbol condition limit unit min typ max operating supply current idd1 fosc = 8 mhz. vdd = 3 v 1.0 1.8 ma idd2 fx = 32 khz. vdd = 3 v 4.8 17 a supply current at halt idd3 fx = 32 khz. vdd = 3 v. ta = 25 c 2.7 5 a idd4 fx = 32 khz. vdd = 3 v. ta = 70 c 13 a supply current at stop idd5 vdd = 3 v. ta = 25 c 2 a vdd = 3 v. ta = 70 c 8 a note) limit: mask rom version
mad00070dem MN101CA27, mn101cfa2d ? pin assignment lqfp064-p-1414 seg5 seg4 seg3 seg2 seg1 seg0 com3 com2 com1 com0 vlc3, mmod vlc2 vlc1 vd d osc1 osc2 p1 7 p1 6 p1 5 p1 4 p1 3 tm1o, p1 2 tm0o, p1 1 buzzer, p1 0 key3, p0 3 key2, p0 2 key1, p0 1 key0, p0 0 nrst , p27 vs s xi xo seg22 seg23 p37, seg24 p36, seg25 p35, seg26 p34, seg27 p33, seg28 p32, seg29 p31, seg30 p30, seg31 p21, rmout p20, irq 2 p07, key 7 p06, key 6 p05, key 5 p04, key 4 seg21 seg20 seg19 seg18 seg17 seg16 seg15 seg14 seg13 seg12 seg 11 seg10 seg 9 seg 8 seg 7 seg 6 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
request for your special attention and precautions in using the technical information and semiconductors described in this book (1) if any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and regulations of the exporting country, especially, those with regard to security export control, must be observed. (2) the technical information described in this book is intended only to show the main characteristics and application circuit examples of the products. no license is granted in and to any intellectual property right or other right owned by panasonic corporation or any other company. therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other company which may arise as a result of the use of technical information described in this book. (3) the products described in this book are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). consult our sales staff in advance for information on the following applications: ? special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the prod- ucts may directly jeopardize life or harm the human body. ? any applications other than the standard applications intended. (4) the products and product specifications described in this book are subject to change without notice for modification and/or im- provement. at the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date product standards in advance to make sure that the latest specifications satisfy your requirements. (5) when designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions (operating power supply voltage and operating environment etc.). especially, please be careful not to exceed the range of absolute maximum rating on the transient state, such as power-on, power-off and mode-switching. otherwise, we will not be liable for any defect which may arise later in your equipment. even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (6) comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (esd, eos, thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. when using products for which damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages. (7) this book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of our company. 20080805
|
